Radio Shack Presidian User's Guide download pdf

Fully-Automatic

Belt Drive Turntable

with Pre-Amp

42-7012

Note: The LIN (lead in), RET (auto return),

and SW (tone arm switch) screws on the

bottom of the turntable are set at the factory

and should not be adjusted.

1. Open the dust cover.

2. Rotate the turntable’s platter until one of

the platter’s two larger holes is above

the drive motor spindle on the

turntable’s upper left side.

3. Remove the tape and two ribbons from

the rubber drive belt. Be sure the belt is

not twisted.

4. Using your fingers, securely seat the

belt on the center of the drive motor’s

spindle (against the lower rim).

5. Plug the turntable’s power cord into a

standard AC outlet.

6. Remove the wire tie from the tone arm,

then press CUE to raise the tone arm.

7. Press PLAY and let the motor rotate the

turntable six or seven times, then press

STOP and check the location of the belt

on the spindle. If the belt is not securely

seated around the spindle, reposition it

properly and repeat Step 6.

Note: If the belt slips off the spindle, do not

attempt to remove the platter. Take it to your

local RadioShack store for assistance.

8. Unplug the turntable’s power cord from

the AC outlet.

9. Connect the turntable’s ground wire to

the amplifier’s/receiver’s GND or earth

terminal to avoid hum.

10. Place the rubber mat, ridged side down,

on top of the platter.

Assemble Your Turntable

Thank you for buying the RadioShack LAB-1200 Fully-Automatic

Belt Drive Turntable. This is a high quality stereo turntable with

sensitive pickup and a built-in pre-amp that delivers great sound

from your records.

Tone arm

Dust cover

Rubber mat

45 RPM adapter

PLAY STOP

CUE

Connect Your Turntable

Connecting Your Turntable to a Receiver/Amplifier

You can connect your LAB-1100 to a receiver/amplifier (or stereo audio

mixer) that has low-level phono inputs (such as left and right PHONO

jacks) or line-level inputs (such as left and right AUX, TV, TAPE, or CD

jacks).

Cautions:

• Do not connect the turntable to AC power until you complete all other

connections.

• Do not place the turntable on top of the receiver/amplifier or on any

other component that gets hot.

• To avoid possible damage to your receiver/amplifier, turn it off before

making the connections

Note: If you are not sure which type of input your receiver/amplifier has,

check your receiver’s/amplifier’s owner’s manual.

Low Level Inputs

To connect the turntable to a low-level phono input, plug the white

and red plugs into the receiver’s/amplifier’s left and right PHONO

jacks. Then set LINE OUT ON/PHONO OUT OFF to

PHONO OUT OFF.

Line Level Inputs

To connect the turntable to a line-level input, plug the white and red

plugs into the receiver’s/amplifier’s left and

right AUX, TV, TAPE, or CD jacks. Then set

LINE OUT ON/PHONO OUT OFF to LINE

OUT ON.

Connecting to Power

Once you have connected the turntable to your

receiver/amplifier, plug the turntable’s power

cord into an AC outlet on your receiver/amplifier

or into a standard AC outlet.

Caution: To prevent electric shock, the plug’s blades are polarized and

fit only one way. If the plug does not fit easily, turn it over and try again.

Note: Depending on if your sound system has

PHONO jacks or not, be sure to set

LINE OUT ON/ PHONO OUT OFF as described in

“Connect Your Turntable”.

1. Open the dust cover.

2. Remove the stylus cover.

3. If you are playing a 33

/3 RPM record, place it

directly over the spindle. If you are playing a 45

RPM record, place the supplied 45 RPM

adapter over the turntable spindle, then place

the record over the adapter.

4. Press SPEED in or out to set the turntable’s

speed (33

/3 or 45 RPM).

5. Press PLAY. The turntable starts to rotate and

the tone arm moves to the beginning of the

record, lowers to the record, then starts to play.

6. At the end of the record, the tone arm

automatically returns to the tone arm rest and

the turntable stops. To stop playing the record

sooner, press STOP. If the tone arm does not

automatically return when it reaches the end of

the record, press STOP to reset the

mechanism.

Using The Cue Button

1. Press CUE to raise the tone arm.

2. Push the tone arm to a spot directly over the

desired part of the record. The turntable starts

to rotate.

3. Press CUE again. The tone arm slowly lowers

and the record plays.

Use Your Turntable

The lightning symbol is intended to alert you to the presence of

uninsulated dangerous voltage within this product’s enclosure

that might be of sufficient magnitude to constitute a risk of

electric shock. Do not open the product’s case.

The exclamation symbol is intended to inform you that

important operating and maintenance instructions are

included in the literature accompanying this product.

WARNING: To reduce the risk of fire or shock hazard, do not

expose this product to rain or moisture.

CAUTION

CAUTION:

TO REDUCE THE

RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER OR

BACK. NO USER-

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Rear View

SPEED

Phono Plugs

Ground Cable

Power Cord

Stylus cover

RadioShack and RadioShack.com are trademarks 04A04

used by RadioShack Corporation.

What’s Included

User’s Guide - Turntable

Rubber Turntable Mat - 45 RPM adapter

42-7012.fm Page 1 Thursday, April 22, 2004 1:38 PM

1 2

Summary of Contents

Page 1 - Belt Drive Turntable

Fully-AutomaticBelt Drive Turntablewith Pre-Amp42-7012Note: The LIN (lead in), RET (auto return), and SW (tone arm switch) screws on the bottom of the

Page 2 - Service & Repair

This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date

Comments to this Manuals

No comments

Radio Shack Presidian User's Guide

Browse online or download User's Guide for Telephones Radio Shack Presidian. Radio Shack Presidian User`s guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Telephones Radio Shack Presidian