Radio-shack PRO-137 User Manual download pdf

20-137

Printed in China

UBZZ69352ZZ(0)

09A07

RACING SCANNER

1. Slide open the battery compartment cover on the back of

the scanner.

2. Set the switch according to

the type of batteries you are

installing: ALKALINE or Ni-MH.

3. Place 3AA batteries into the

battery compartment.

4. Replace the cover.

To charge batteries:

1. Set the switch to Ni-MH.

2. Install rechargeable batteries.

3. Connect an external power source to the 6V 800mA jack.

Note: The scanner stops charging automatically after a maximum of 14 hours.

Step 1: Insert Batteries

Attach the supplied antenna to

the scanner by screwing it tightly

onto the anchor post at the top of

the radio.

When using an external antenna,

always use 50-ohm, RG-58, or

RG-8, coaxial cable to connect

to it. If the antenna is over 50

feet from the scanner, use RG-8

low-loss dielectric coaxial cable.

If your antenna’s cable does not

have a SMA connector, your local

RadioShack store carries a variety

of SMA adapters.

Step 2: Install Antenna

Turning on the Scanner

Press and hold / .

Setting the Volume

1. Push the SEL/VOL/SQL knob.

2. Rotate the knob to select the volume level from 0 to 15.

Setting the Squelch

1. Press Func.

2. Push the SEL/VOL/SQL knob.

3. Rotate the knob to select the squelch level from 0 to 15.

Step 3: Basic Operations

Before You Get to the Track

Your scanner is preprogrammed with all of the

drivers and their possible frequencies that were

known when it was manufactured.

Before you leave for the track, check the

Internet to see if there are any frequency

updates available for your race. You can save

time at the track by setting up as much as

possible before you leave.

When You Get to the Track

When you arrive at the race, get a list of the

frequencies in use that race day. These are

normally available for sale on the way into the

facility. This list will show the actual frequency

being used by each driver that day, as well as

some other useful frequency information.

Then, follow the steps in the following sections

to adjust the scanner settings.

Load the Preset Race Frequency List

For your convenience, six car race frequencies

are preprogrammed. You can use one of these

race frequencies by loading it to the channel

banks.

To load the race frequencies:

1. Press Menu.

2. Rotate the knob to select 1: Preset Race, then

press E

PGM.

3. Rotate the knob to select 1: Load Race, then

press E

PGM

4. Rotate the knob to select one of the races,

then press E

PGM

5. If you select races A, B or C, Load Bank X into

Bank 0 Yes=”1” / No=”3” appears.

If you select races D, E, or F, Load Bank X into

Bank 0 and 1 Yes=”1” / No=”3” appears.

6. Press 1 to program the race or press 3 to

cancel.

Program Driver Frequencies

To select the appropriate frequency for each

driver:

1. Press CAR, enter the car’s number, then

press E

PGM

2. If the car number is not stored, Car# XX is

not stored. Program new car? Yes = “E” / No = “.”

appears.

3. Press E

PGM

to edit the tag.

4. Enter the tag you want to assign to the car

number (such as driver’s name), then press

PGM

5. Enter the frequency of the car, then press

PGM

6. If you want to input another frequency to

the car, press E

PGM

To edit a tag:

• Press the number/letter buttons multiple

times until the desired letter appears.

• Rotate the knob clockwise to move the

cursor to the left, counterclockwise to

move to the right.

• Press Func to toggle the input mode

between ABC, abc, and 123.

• Press •CLR once to erase one character.

Press and hold to erase all characters.

• Press E

PGM

to save the tag and exit editing

tag.

Monitor a Car

To listen to the transmissions from one car:

1. Press CAR, enter the car number, then

press E

PGM

1. Select the car from a list. Press CAR then

press E

PGM

2. Rotating the knob to the desired car, then

press E

PGM

Select the Car’s Primary Frequency

Primary frequency is the frequency which is

selected ﬁrst when a car has two or more

frequencies. By default, the frequency in

the smallest channel works as the primary

frequency.

To change a car’s primary frequency:

1. Show the channel where the car number is

programmed.

2. Press the Func key and rotate the knob to

select the other frequency.

Primary frequency is also changed automatically

in the following situations:

• Selecting car channel by rotating the knob

during manual mode.

• Pressing SCAN when you monitor a car

channel found by scan mode.

Step 4: Using Your Scanner at the Racetrack

Warning: Only set the switch inside the

battery compartment to Ni-MH for use

with Ni-MH rechargeable batteries. Never

use non-rechargeable batteries when the

switch is set to Ni-MH.

Func

PRO-137

20-137

Quick Start Guide

Radio-shack PRO-137 User Manual

Browse online or download User Manual for Scanners Radio-shack PRO-137. Radio Shack PRO-137 User Manual

Summary of Contents

Comments to this Manuals

Radio-shack PRO-137 User Manual

Browse online or download User Manual for Scanners Radio-shack PRO-137. Radio Shack PRO-137 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Scanners Radio-shack PRO-137