Radio Shack ET-1125 Owner's Manual

Cat. No. 43-1125 OWNER’S MANUALPlease read before using this equipment.ET-1125900 MHz Digital Spread SpectrumCordless Telephonewith Caller ID/Call Wai

10• If the display is blank and the phonedoes not work, recharge the batterypack. (The battery power might betoo low to light the display.)• If you ar

11TURNING AUTO TALKON/OFFYour phone is preset so you must pressTALK when you lift the handset from thebase to answer a call. With auto talkturned on,

123. Press CH/SELECT, then enter yourthree-digit area code. If you make amistake, repeatedly press / or #/ to move the cursor over the in-correct di

13OPERATIONA QUICK LOOK AT YOUR PHONEUse FUNCTION to selectyour phone’s functions.Use TALK to make acall (see “Making andReceiving Calls” onPage 14).U

14MAKING AND RECEIVING CALLSTo make a call, lift the handset andpress TALK. Talk and the current vol-ume setting (see “Adjusting the HandsetVolume”) a

15Notes:• You can also press REDIAL/PAUSEafter pressing TALK to dial the lastnumber dialed.• The redial memory holds up to 32digits, so you can redial

16MEMORY DIALINGYou can store up to 20 phone numbersand names in memory, then dial a storednumber by entering its memory locationnumber. Each number c

17Editing or Deleting a Number in MemoryFollow these steps to edit or delete amemory number.1. Lift the handset. 2. Hold down MEM until MemoryStore an

18You can also dial a memory number af-ter pressing TALK. Press MEM (the dis-play does not change but the phone’smemory recall activates) then enter a

19CALLER ID OPERATIONIf you subscribe to Caller ID service fromyour phone company, the phone compa-ny sends information about the call, aswell as the

2FEATURESYour RadioShack 900 MHz DigitalSpread Spectrum Cordless Telephoneuses advanced technology to give yousuperior audio quality and extendedrange

20Caller ID MessagesADDING/DELETING THE AREA CODEWhen the area code of the received callis the same as the one you stored (see“Storing Your Area Code”

21STORING A CALLER ID RECORD TO MEMORYFollow these steps to store the nameand number from a Caller ID record intoa memory location.1. Press CALL ID th

22TROUBLESHOOTING We do not expect you to have any problems with your phone, but if you do, thesesuggestions might help. Problem SuggestionThe phone d

23If you still have problems, disconnect the phone. If other phones on the same linework properly, the fault is in this phone or its installation. If

24CARE AND MAINTENANCEYour RadioShack 900 MHz Digital Spread Spectrum Cordless Telephone is an ex-ample of superior design and craftsmanship. The foll

25REPLACING THE BATTERY PACKIf you follow the instructions in “Connect-ing and Charging the Battery Pack” onPage 8, the battery pack should lastabout

26advance. If advance notice is not practi-cal, the phone company notifies you assoon as possible and advises you ofyour right to file a complaint wit

27NOTES

RadioShack CorporationFort Worth, Texas 76102UCZZ01673ZA09A00 Printed in ChinaLimited One-Year WarrantyThis product is warranted by RadioShack against

3Security Access-Protection Code —automatically prevents other cordlessphone users from using your phone linewhile the handset is off the base.Auto Ta

4If you use more than one phone or otherdevice on the line, add up all of theRENs. If the total is more than five (orthree in rural areas), your telep

5CONTENTSInstallation ... 6Mounting the P

6INSTALLATIONMOUNTING THE PHONEYou can place the phone on a desk ortable, mount it on a standard wall plate,or mount it directly on a wall.Select a lo

73. Route the adapter’s cord throughthe strain relief slot on the base.4. Plug the modular cord’s other endinto the phone jack.5. Plug the adapter int

87. Lift the base’s antenna to a verticalposition.Note: To mount the phone directly on awall, you need two screws (not supplied)with heads that fit in

92. Lift the battery pack out of the com-partment. 3. Plug the battery pack’s connector in-to the socket in the compartment,(the connector fits only o